Hyundai Accent: Clutch System / Ignition Lock Switch
| Item | Specifications |
| Working voltage | DC 12.5V ± 0.3V |
| Operating force | Initial position : 0.25 ± 0.15N(0.025 ± 0.015kg, 0.056 ± 0.034lb) |
| Full position : 0.8 ± 0.2 N(0.08 ± 0.02 kgf, 0.579 ± 0.014 lb-ft) | |
| Working temperature | -40℃ ~ 80℃ (-40℉ ~ 176℉) |
– Ignition lock switch is mounted on the clutch pedal.
– Ignition lock switch is operated when you press the clutch pedal.
– If the clutch pedal is not pressed down, the engine is not started.
Ignition lock & clutch switch operating locus
– If the clutch pedal is pressed down, (B) operate ignition lock switch at a location.
| Engine | Operation switch stroke | ||
| Gasoline 1.6 | Clutch switch ON -> OFF (A) | Ignition lock switch OFF -> ON (B) | Switch full stroke (C) |
| 87.5˚ ± 3˚ | 110˚ ± 5.5˚ | 117.3˚ | |
1.Turn ignition switch OFF and disconnect the negative (-) battery cable.
2.Disconnect the ignition lock & clutch switch connector (A).
3.Remove the ignition lock & clutch switch (A) after loosening the bolts (B).
Component Inspection
1.Turn ignition switch OFF and disconnect the negative (-) battery cable.
2. Remove the ignition lock & clutch switch.
3.Rotate the switch lever to the direction of the arrow to check the operating point (A).
1.Install is proceeds as follows.※ How to install the ignition lock & clutch switch(A) After inserting the switch lever (A) into the clutch pedal pin (B), pre-tighten the switch mounting bolts (C).(B) Set the clutch switches so as to confirm that the electric current is applied to the pins ① and ③.(C) Fix the clutch pedal to the ignition lock switch OFF→ON strokes (F).(D) With the pedal fixed, rotate the switch clockwise and counter-clockwise to set it to a position at the transition from OFF to ON. Then, tighten the mounting bolts (C) to the specified torque.(E) Once completing the assembly, check again that the switch is correctly operating.※ OFF→ON stroke tolerance should be within ± 7.7 mm (0.3031 in.)
OFF → ON Position (F) :121.8 ± 7.7 mm (4.7953 ± 0.3031 in.)Tightening torque :2.0 - 3.9 N.m (0.2 - 0.4 kgf.m, 1.4 - 2.9 lb-ft)
Other information:
Hyundai Accent (HC) (2017 - 2022) Service Manual: General Information
- General Troubleshooting Information Before Troubleshooting 1.Check applicable fuses in the appropriate fuse/relay box. 2.Using the battery checker (MCR-570 KIT), check the battery for damage, state of charge, and clean and tight connections.(Refer to Engine Electrical System - "Battery") • Do not quick-charge a battery unless the battery ground cable has been disconnected, otherwise you will damage the alternator diodes.Hyundai Accent (HC) (2017 - 2022) Service Manual: Timing Chain
- Removal 1.Disconnect the battery negative terminal. 2.Turn the crankshaft damper pulley clockwise, and align its groove with the timing mark of the timing chain cover. 3.Remove the timing chain cover.(Refer to Timing System - "Timing Chain Cover") 4.Remove the cam to cam guide (A). 5.Remove the timing chain tensioner (A) and remove the timing chain tensioner arm (B).
Categories
- Manuals Home
- Hyundai Accent Owners Manual
- Hyundai Accent Service Manual
- New on site
- Most important about car
