Hyundai Accent (HC): Clutch System / Ignition Lock Switch

- Specifications

ItemSpecifications
Working voltageDC 12.5V ± 0.3V
Operating forceInitial position : 0.25 ± 0.15N(0.025 ± 0.015kg, 0.056 ± 0.034lb)
Full position : 0.8 ± 0.2 N(0.08 ± 0.02 kgf, 0.579 ± 0.014 lb-ft)
Working temperature-40℃ ~ 80℃ (-40℉ ~ 176℉)

- Description

– Ignition lock switch is mounted on the clutch pedal.

– Ignition lock switch is operated when you press the clutch pedal.

– If the clutch pedal is not pressed down, the engine is not started.

Ignition lock & clutch switch operating locus

– If the clutch pedal is pressed down, (B) operate ignition lock switch at a location.

EngineOperation switch stroke
Gasoline 1.6Clutch switch ON -> OFF (A)Ignition lock switch OFF -> ON (B)Switch full stroke (C)
87.5˚ ± 3˚110˚ ± 5.5˚117.3˚

- Removal

1.Turn ignition switch OFF and disconnect the negative (-) battery cable.

2.Disconnect the ignition lock & clutch switch connector (A).

3.Remove the ignition lock & clutch switch (A) after loosening the bolts (B).

- Inspection

Component Inspection

1.Turn ignition switch OFF and disconnect the negative (-) battery cable.

2. Remove the ignition lock & clutch switch.

3.Rotate the switch lever to the direction of the arrow to check the operating point (A).

- Installation

1.Install is proceeds as follows.※ How to install the ignition lock & clutch switch(A) After inserting the switch lever (A) into the clutch pedal pin (B), pre-tighten the switch mounting bolts (C).(B) Set the clutch switches so as to confirm that the electric current is applied to the pins ① and ③.(C) Fix the clutch pedal to the ignition lock switch OFF→ON strokes (F).(D) With the pedal fixed, rotate the switch clockwise and counter-clockwise to set it to a position at the transition from OFF to ON. Then, tighten the mounting bolts (C) to the specified torque.(E) Once completing the assembly, check again that the switch is correctly operating.※ OFF→ON stroke tolerance should be within ± 7.7 mm (0.3031 in.)

OFF → ON Position (F) :121.8 ± 7.7 mm (4.7953 ± 0.3031 in.)Tightening torque :2.0 - 3.9 N.m (0.2 - 0.4 kgf.m, 1.4 - 2.9 lb-ft)

Other information:

Hyundai Accent (HC) (2017 - 2022) Service Manual: Troubleshooting

- Trouble Symptom Charts Trouble Symptom 1 Trouble Symptom 2 Trouble symptomProbable causeRemedy The set vehicle speed varies greatly upward or downward"Surging" (repeated alternating acceleration and deceleration) occurs after settingMalfunction of the vehicle speed sensor circuitRepair the vehicle speed sensor system, or replace the part Malfunction of ECMCheck input and output signals at ECM Trouble Symptom 3 Trouble symptomProbable causeRemedy The CC system is not canceled whe

Hyundai Accent (HC) (2017 - 2022) Service Manual: Specifications

- Specifications ItemsSpecification HoodTypeFront opening type, rear hinged, stay rod type Front DoorConstructionFront hinged, frame door construction Regulator systemWire drum type Locking systemPin - fork system Rear DoorConstructionFront hinged, frame door construction Regulator systemWire drum type Locking systemPin - fork system Trunk LidTypeTorsior bay type Seat BeltsFront3 point type with Emergency Locking Retractor (E.

Categories


 
Copyright © 2025
0.005