Hyundai Accent (HC): IVT Control System / Position Switch
| Item | Specification |
| Power supply (V) | 4.5 - 5.5V |
| Output type | PWM (S1, S2), ON/OFF (Ps, Ns) |
1. Position switch
2. Manual control lever
• Inspect the connector thoroughly for looseness, poor connection, bending, corrosion, contamination, deformation, or damage.
1.Disconnect the parking switch connector.
2.Turn Ignition "ON", & engine "OFF".
3.Measure the output signal in each range (P, R, N, D).
| Signal | P | R | N | D |
| S1 | 18.30% | 47.50% | 64.60% | 81.70% |
| S2 | 81.70% | 52.50% | 35.40% | 18.30% |
| Pin | Connection information |
| 1 | Power (Ps,Ns) |
| 2 | Back-up lamp |
| 3 | Power (Back-up lamp) |
| 4 | Ps ,Ns |
| 5 | Power (5V) |
| 6 | Ground (5V) |
| 7 | S1 |
| 8 | S2 |
1.Shift the gear to "N".
2.Remove the air cleaner assembly.(Refer to Engine Mechanical System - "Air Cleaner")
3.Disconnect the position switch connector (A) and loosen the shift cable mounting nut (B).
4.Remove the manual control lever (A) and the washer after removing a nut.
5.Remove the position switch (A) after removing the bolts.
1.Check that the gear is shifted to "N".
2.Lightly tighten the bolts after installing the position switch (A).
3.Lightly tighten the nut after installing the manual control lever (A).
4.Align the hole in the manual control lever with the "N" position hole of the position switch and then insert the SST position switch guide pin (09480 - A3800).
5.Tighten the manual control lever nut (A) with specified toque.
Tightening torque :17.7 - 24.5 N.m (1.8 - 2.5 kgf.m, 13.0 - 18.1 lb-ft)
6.Tighten the position switch bolts (A) with specified toque.
Tightening torque :9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)
7.Push nut (A) lightly to "F" direction shown to eliminate free play of shift cable.
8.Tighten the nut (A) with the specified torque.
Tightening torque :9.8 - 14.7 N.m (1.0 - 1.5 kgf.m, 7.2 - 10.8 lb-ft)
9.Remove the SST (09480-A3800) from the adjusment hole.
10.Connect the position switch connector (A).
11.Install the air cleaner assembly.(Refer to Engine Mechanical System - "Air cleaner")
Other information:
Hyundai Accent (HC) (2017 - 2022) Service Manual: Timing Chain
- Removal 1.Disconnect the battery negative terminal. 2.Turn the crankshaft damper pulley clockwise, and align its groove with the timing mark of the timing chain cover. 3.Remove the timing chain cover.(Refer to Timing System - "Timing Chain Cover") 4.Remove the cam to cam guide (A). 5.Remove the timing chain tensioner (A) and remove the timing chain tensioner arm (B).Hyundai Accent (HC) (2017 - 2022) Service Manual: Troubleshooting
- Troubleshooting Problem Symptoms Table Use the table below to help you find the cause of the problem. The numbers indicate the priority of the like cause of the problem. Check each part in order.If necessary, replace these parts.SymptomSuspect AreaReference Lower pedal or spongy pedal1. Brake system (Fluid leaks)2. Brake system (Air in)3. Piston seals (Worn or damaged)4.
Categories
- Manuals Home
- Hyundai Accent Owners Manual
- Hyundai Accent Service Manual
- Questions & Answers
- Video Guides
- Useful Resources
- New on site
- Most important about car
- Privacy Policy
0.0051