Hyundai Accent (HC): Body (Interior and Exterior) / Rear Seat Belt

Contents:

Components and Components Location

- Components

1. Rear seat belt buckle [LH]
2. Rear seat belt buckle [RH]
3. Rear center seat belt buckle
4. Rear seat belt retractor [LH]
5. Rear seat belt retractor [RH]
6. Rear center seat belt retractor


Rear Seat Belt Retractor

- Component Location

1. Rear seat belt retractor [LH]
2. Rear seat belt retractor [RH]


- Replacement

   

• When installing the belt, make sure not to damage the retractor.

1.Remove the package tray trim.(Refer to Interior Trim - "Package Tray Trim")

2.After loosening the mounting bolt, remove the rear seat belt lower anchor (A).

Tightening torque :39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.8 - 39.8 lb-ft)

3.Loosen the retractor (A) mounting bolt, remove the rear seat belt (B).[LH]

Tightening torque :39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.8 - 39.8 lb-ft)

[RH]

Tightening torque :39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.8 - 39.8 lb-ft)

4.To install, reverse the removal procedure.

   

• Replace any damaged clips (or pin - type retainers).

Rear Center Seat Belt Retractor

- Component Location

1. Rear center seat belt retractor


- Replacement

   

• When installing the belt, make sure not to damage the retractor.

1.Remove the package tray trim.(Refer to Interior Trim - "Rear Package Tray Trim")

2.After loosening the mounting bolts, remove the rear center seat belt retractor (A).

Tightening torque :39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.8 - 39.8 lb-ft)

3.To install, reverse the removal procedure.

   

• Replace any damaged clips.

Rear Seat Belt Buckle

- Component Location

1. Rear seat belt buckle [RH]
2. Rear seat belt buckle [Center]
3. Rear center seat belt buckle [LH]


- Replacement

1.Remove the rear seat cushion assembly.(Refer to Rear Seat - "Rear Seat Cushion Assembly")

2.Loosen the mounting bolt, remove the rear seat belt buckle (A).[LH]

Tightening torque :39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.9 - 39.8 lb-ft)

[RH, Center]

Tightening torque :39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.9 - 39.8 lb-ft)

3.To install, reverse the removal procedure.

   

• The buckle and tongue of different types are impossible to be latched, so check that the buckle & tongue have the same types.

• Distinguish the rear side seat buckle from the center seat buckle before latching.

• If foreign materials are stuck in the inside button of buckle, it may cause interference during the latching process, leading to a functional problem (for example - beverages (viscous drinks), toothpicks, sand, plastic, vinyl, metal pieces, etc.)

• After latching the buckle and tongue, check the fastening force using a Push - Pull Gauge (fastening force: 3kgf or less).

Other information:

Hyundai Accent (HC) (2017 - 2022) Service Manual: Variable Intake Solenoid (VIS) Valve

- Description Variable Intake manifold Solenoid (VIS) valve is installed on the intake manifold. The VIS valve controls the vacuum modulator which activates a valve in the intake manifold. The ECM opens or closes this valve according to engine condition (Refer to below table). Engine conditionVIS valveOperation Medium speedClosedIncreasing engine performance in low engine speed by reducing intake interference among cylinders Low / High speedOpenMinimizing intake resistance by shortening intake manifold length and increasing area of air entrance - Specification ItemSpecification Coil resistance (Ω)30.

Hyundai Accent (HC) (2017 - 2022) Service Manual: TPMS Sensor

- Description 1.General descriptionWU is a sensor placed in the tire that reports pressure and temperature.The WU is mounted inside the wheels, fixed to the valve. The angle between the valve and the housing of the WU is variable.This allows adaptation to various types of rims.The Wheel Unit is made of a PCB supporting the electronic hardware and encapsulated inside a housing which is potted with polyurethane.

Contents

Categories


 
Copyright © 2025
0.0046