Hyundai Accent (HC): Engine Control / Fuel System / Specifications

Hyundai Accent (HC) (2017 - 2022) Service Manual / Engine Control / Fuel System / Specifications

- Specifications Fuel Delivery System

ItemsSpecification
Fuel TankCapacity43 lit. (11.4 U.S.gal., 45.4 U.S.qt., 37.8 Imp.qt.)
Fuel Filter
(built in Fuel Pump Assembly)		TypePaper type
Fuel Pressure Regulator
(built in Fuel Pump assembly)		Regulated Fuel Pressure323 ~ 363kpa (3.29 ~ 3.70kgf/cm, 46.79 ~ 52.63 psi)
Fuel PumpTypeElectrical, in-tank type
Driven byElectric motor
Fuel Retrun SystemTypeReturnless

Sensors

Manifold Absolute Pressure Sensor (MAPS)

▷ Type : Piezo-resistive pressure sensor type▷ Specification
Pressure (kPa)Output Voltage (V)
10.00.5
62.52.5
1154.5

Intake Air Temperature Sensor (IATS)

▷ Type : Thermistor type▷ Specification
Temperature [°C (°F)]Resistance (kΩ)
-40 (-40)38.88 ~ 50.77
-20 (-4)13.19 ~ 16.82
0 (32)5.11 ~ 6.11
20 (68)2.19 ~ 2.69
40 (104)1.02 ~ 1.26
60 (140)0.51 ~ 0.64
80 (176)0.27 ~ 0.35

Engine Coolant Temperature Sensor (ECTS)

▷ Type : Thermistor type▷ Specification
Temperature [°C (°F)]Resistance (kΩ)
-40 (-40)41.74 ~ 54.54
-30 (-22)23.54 ~ 29.94
-20 (-4)14.13 ~ 16.83
-10 (14)8.39 ~ 10.22
0 (32)5.28 ~ 6.29
10 (50)3.42 ~ 4.00
20 (68)2.31 ~ 2.59
30 (86)1.55 ~ 1.86
40 (104)1.08 ~ 1.21
50 (122)0.77 ~ 0.85
60 (140)0.56 ~ 0.61
70 (158)0.41 ~ 0.44
80 (176)0.31 ~ 0.33
90 (194)0.23 ~ 0.25
100 (212)0.18 ~ 0.19

Throttle Position Sensor (TPS)

▷ Type : Absolute Rotary Sensor IC▷ Specification

Heated Oxygen Sensor (HO2S) [Bank 1 / Sensor 1]

▷ Type : Zirconia (ZrO2) type▷ Specification
ItemResistance (Ω)
Heater Resistance (Ω)Approx. 2.5 (20°C)

Heated Oxygen Sensor (HO2S) [Bank 1 / Sensor 2]

▷ Type : Zirconia (ZrO2) type▷ Specification
ItemResistance (Ω)
Heater Resistance (Ω)Approx. 3.0 (20°C)

Camshaft Position Sensor (CMPS)

▷ Type : Hall effect type

Crankshaft Position Sensor (CKPS)

▷ Type : Magnetic field sensitive Type

Knock Sensor (KS)

▷ Type : Piezo-electricity type▷ Specification
ItemSpecificationRemarks
Capacitance (pF)850 ~ 11501 Khz
Insulation registance (MΩ)850 ~ 1150Pin to Body

Accelerator Position Sensor (APS)

▷ Type : Inductiv type▷ Specification
ItemsSpecification
APS 1APS 2
C.T0.7 ~ 0.80.33 ~ 0.43
W.O.T4.13 ~ 4.222.04 ~ 2.13

Fuel Tank Pressure Sensor (FTPS)

▷ Type : Piezo - Resistivity type ▷ Specification
Pressure
[kPa (kgf/cm², in H2O)		Output Voltage (V)
-6.67 (-0.068, -26.8)0.5
02.5
+6.67 (0.068, 26.8)4.5

Actuators

Injector

▷ Number : 8▷ Specification
ItemSpecification
Coil Resistance (Ω)11.4 ~ 12.6 [20°C (68°F)]

Purge Control Solenoid Valve (PCSV)

▷ Specification
ItemSpecification
Coil Resistance (Ω)12.5 ~ 16.5 [20°C (68°F)]

Variable Force Solenoid (VFS) [Bank 1/ Intake, Exhaust]

▷ Specification
ItemSpecification
Coil Resistance (Ω)5.2 ~ 5.9 [20°C (68°F)]
Operating Voltage (V)10 ~ 16

Variable Intake Solenoid (VIS) Valve

▷ Specification
ItemSpecification
Coil Resistance (Ω)30.0 ~ 35.0 [20°C (68°F)]

ETC Motor

▷ Specification
ItemSpecification
Coil Resistance (Ω)1.4 ~ 1.5 [25 ± 5°C (77 ± 41°F)]

Canister Close Valve (CCV)

▷ Specification
ItemSpecification
Coil Resistance (Ω)19.8 - 20.8 (20°C)

- Service Standard
Ignition TimingBTDC 2° ± 10°
Idle SpeedA/CON OFFNeutral, N, P-range630 ± 100
D-range630 ± 100
A/CON ONNeutral, N, P-range630 ± 100
D, R-range680 ± 100

- Tightening Torques

Engine Control System

Itemkgf.mN.mlb-ft
ECM installation nuts [A/T]1.0 ~ 1.29.8 ~ 11.87.2 ~ 8.7
ECM installation screws [M/T]0.092 ~ 0.0960.9 ~ 0.950.6 ~ 0.7
ECM bracket installation bolt1.0 ~ 1.29.8 ~ 11.87.2 ~ 8.7
ECM bracket installation nut1.0 ~ 1.29.8 ~ 11.87.2 ~ 8.7
Manifold absolute pressure sensor installation bolt0.7 ~ 0.96.9 ~ 8.85.1 ~ 6.5
Engine coolant temperature sensor installation3.0 ~ 4.029.4 ~ 39.221.7 ~ 28.9
Crankshaft position sensor installation bolt0.8 ~ 1.27.8 ~ 11.85.8 ~ 8.7
Camshaft position sensor (Bank 1 / Intake) installation bolt0.8 ~ 1.27.8 ~ 11.85.8 ~ 8.7
Camshaft position sensor (Bank 1 / Exhaust) installation bolt0.8 ~ 1.27.8 ~ 11.85.8 ~ 8.7
Knock sensor installation bolt1.9 ~ 2.518.6 ~ 24.513.7 ~ 18.1
Heated oxygen sensor (Bank 1 / Sensor 1) installation4.0 ~ 5.039.2 ~ 49.128.9 ~ 36.2
Heated oxygen sensor (Bank 1 / Sensor 2) installation4.0 ~ 5.039.2 ~ 49.128.9 ~ 36.2
ETC (Electronic Throttle Control) module installation bolt1.0 ~ 1.29.8 ~ 11.87.2 ~ 8.7
CVVT oil control valve (Bank 1 / Intake) installation bolt1.0 ~ 1.29.8 ~ 11.87.2 ~ 8.7
CVVT oil control valve (Bank 1 / Exhaust) installation bolt1.0 ~ 1.29.8 ~ 11.87.2 ~ 8.7
Ignition coil installation bolt1.0 ~ 1.29.8 ~ 11.87.2 ~ 8.7
Variable intake solenoid valve bracket installtion bolt1.0 ~ 1.29.8 ~ 11.87.2 ~ 8.7

Fuel Delivery System

Itemkgf.mN.mlb-ft
Fuel tank installation nut4.0 ~ 5.539.2 ~ 53.928.9 ~ 39.8
Fuel pump plate cover installation bolt0.2 ~ 0.32.0 ~ 2.91.4 ~ 2.2
Filler-neck assembly installation bolt0.8 ~ 1.27.8 ~ 11.85.8 ~ 8.7
Filler-neck assembly installation screw0.8 ~ 1.27.8 ~ 11.85.8 ~ 8.7
Delivery pipe installation bolt2.0 ~ 2.519.6 ~ 24.514.5 ~ 18.1
Delivery pipe installation nut (↔ Fuel feed tube)0.4 ~ 0.63.9 ~ 5.92.9 ~ 4.3
Accelerator pedal installation nut1.3 ~ 1.612.7 ~ 15.79.4 ~ 11.6
Accelerator pedal installation bolt0.9 ~ 1.48.8 ~ 13.76.5 ~ 10.1

Engine Control / Fuel System

Troubleshooting

Other information:

Hyundai Accent (HC) (2017 - 2022) Service Manual: Brake Line

- Components [Disc Type] [Drum Type] - Removal [Brake Tube (Engine Room)] 1.Disconnect the negative (-) battery cable. 2.Disconnect the brake fluid level switch connector. 3.Remove the brake fluid from the master cylinder reservior with a syringe.     • Do not spill brake fluid on the vehicle, it may damage the paint; if brake fluid does contact the paint, wash it off immediately with water.

Hyundai Accent (HC) (2017 - 2022) Service Manual: Blower Unit

- Component Location 1. Blower unit assembly - Components 1. Seal2. Intake duct case3. Intake actuator4. Intake door5. Intake lower case6. Blower upper case7. Blower unit pad8. Blower lower case9. Blower motor10. Air filter11. Air filter cover12. PWM Blower module - Replacement     When prying with a flat-tip screwdriver or use a prying trim tool, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.

Categories


 
Copyright © 2025
0.0063