Hyundai Accent (HC): Steering System

Hyundai Accent (HC) (2017 - 2022) Service Manual / Steering System

Contents:

Specifications

- Specifications

ItemSpecification
TypeElectric Power Steering System
Steering gearTypeRack & Pinion
Rack stroke150 mm (5.90 in.) ± 1 (0.3937 in.)
Steering angle(Max.)Inner39.5°(+0.5°/-1.5°)
Outer32.6°

- Tightening Torques
ItemTightening torque (kgf.m)
N.mkgf.mlb-ft
Hub nuts107.9 - 127.511.0 - 13.079.6 - 94.0
Steering wheel lock bolt44.1 - 49.04.5 - 5.032.5 - 36.2
Steering column mounting Bolt53.9 - 58.85.5 - 6.039.8 - 43.4
Nuts25.0 - 29.42.5 - 3.014.5 - 21.7
Steering column to Universal joint (M8 BOLT) 32.4 - 38.3 3.3 - 3.8 23.9 - 27.5
Steering column to Universal joint (M10 BOLT) 49.0 - 58.8 5.0 - 6.0 36.2 - 43.4
Bolt connecting universal joint to pinion (M8 BOLT)32.4 - 37.33.3 - 3.823.9 - 27.5
Bolt connecting universal joint to pinion (M10 BOLT)49.0 - 58.85.0 - 6.036.2 - 43.4
Tie rod end castle nut 24.5 - 34.32.5 - 3.518.1 - 25.3
Lower arm to front axle 58.8 - 70.66.0 - 7.243.4 - 52.1
Steering gear box to sub frame 88.3 - 107.99.0 - 11.065.1 - 79.6
Stabilizer link nut 98.1 - 117.710.0 - 12.072.3 - 86.8
Sub frame mounting bolts ＆ nuts 156.9 - 176.516.0 - 18.0115.7 - 130.2

Troubleshooting

- Troubleshooting

Trouble SymptomCause of the symptomRemedy
Excessive play in steeringLoose U-joint boltRetighten or replace as necessary
Loose yoke plugRetighten
Loose steering gear mounting boltsRetighten
Loose or worn tie rod endRetighten or replace as necessary
Steering wheel does not return to its original positionExcessive turning resistance of tie rod endReplace
Yoke plug excessively tightAdjust
Tie rod and/or ball joint cannot turn smoothlyReplace
Loose mounting of gear box at the subframeRetighten
Worn steering shaft joint and/or body grommetCorrect or replace
Distorted rackReplace
Rattling or chucking noise in the rack and pinionLoose steering gear box mountingReposition
Loose tie rod end and/or ball jointRepace
Worn tie rod and/or ball jointRepace
Loose yoke plugReplace

Repair procedures

- Inspection Steering Wheel Play Inspection

1.Turn the steering wheel so that the front wheels can face straight ahead.

2.Measure the distance the steering wheel can be turned without moving the front wheels.

Standard value : 30mm (1.18in.) or less

3.If the play exceeds standard value, inspect the steering column, shaft, and linkages.

Checking stationary steering effort

1.Position the vehicle on a level surface and place the steering wheel in the straight ahead position.

2.Attach a spring scale to the steering wheel. With the engine speed 600 ±100 rpm, pull the scale and read it as soon as the tires begin to turn.

Standard value : 3.0kgf or less

3.If the measured value exceeds standard value, inspect the power steering gear box and ESP system.

Steering wheel ➤

Motor Driven Power Steering ➤

Tire Pressure Monitoring System

Steering wheel

Other information:

Hyundai Accent (HC) (2017 - 2022) Service Manual: CVVT & Camshaft

- Description Continuous Variable Valve Timing (CVVT) system advances or retards the valve timing of the intake and exhaust valve in accordance with the ECM control signal which is calculated by the engine speed and load.By controlling CVVT, the valve over-lap or under-lap occurs, which makes better fuel economy and reduces exhaust gases (NOx, HC) and improves engine performance through reduction of pumping loss, internal EGR effect, improvement of combustion stability, improvement of volumetric efficiency, and increase of expansion work.

Hyundai Accent (HC) (2017 - 2022) Service Manual: Troubleshooting

- Basic Troubleshooting Basic Troubleshooting Guide Customer Problem Analysis Sheet Basic Inspection Procedure Measuring Condition Of Electronic Parts' Resistance The measured resistance at high temperature after vehicle running may be high or low. So all resistance must be measured at ambient temperature (20°C, 68°F), unless stated otherwise.

Contents

Categories

 
Copyright © 2025
0.007