Hyundai Accent (HC): Brake System / Brake Line

- Components

[Disc Type]

[Drum Type]

- Removal [Brake Tube (Engine Room)]

1.Disconnect the negative (-) battery cable.

2.Disconnect the brake fluid level switch connector.

3.Remove the brake fluid from the master cylinder reservior with a syringe.

   

• Do not spill brake fluid on the vehicle, it may damage the paint; if brake fluid does contact the paint, wash it off immediately with water.

4.Remove the brake tube from the ESP (ABS), master cylinder and brake tube connector.

Tightening torqueABS : 13.7 - 16.7 N.m (1.4 - 1.7 kgf.m, 10.1 - 12.3 lb-ft)ESP : 18.6 - 22.6 N.m (1.9 - 2.3 kgf.m. 13.7 - 16.6 lb-ft)Brake tube connector : 13.7 - 16.7 N.m (1.4 - 1.7 kgf.m, 10.1 - 12.3 lb-ft)Master cylinder : 13.7 - 16.7 N.m (1.4 - 1.7 kgf.m, 10.1 - 12.3 lb-ft)

   

• When replacing, be careful not to damage the brake tube.

[Brake Hose]

1.Disconnect the negative (-) battery cable.

2.Disconnect the brake fluid level switch connector.

3.Remove the brake fluid from the master cylinder reservior with a syringe.

   

• Do not spill brake fluid on the vehicle, it may damage the paint; if brake fluid does contact the paint, wash it off immediately with water.

4.Remove the wheel & tire.

5.Remove the brake hose clip (A).

6.Disconnect the brake tube by loosening the tube flare nut (B).

Tightening torque :12.7 - 16.7 N.m (1.3 - 1.7 kgf.m, 9.4 - 12.3 lb-ft)

[Front]

[Rear]

7.Disconnect the brake hose by loosening the bolt (A) & (B).

Tightening torque :24.5 - 29.4 N.m (2.5 - 3.0 kgf.m, 18.1 - 21.7 lb-ft)

[Front]

[Rear Disc]

[Rear Drum]

8.Remove the brake hose bracket by loosening the bolt (A). [Drum brake only]

Tightening torque :18.6 - 25.5 N.m (1.9 - 2.6 kgf.m, 13.7 - 18.8 lb-ft)

- Inspection

1.Check the brake tubes for cracks, crimps and corrosion.

2.Check the brake hoses for cracks, damage and fluid leakage.

3.Check the brake tube flare nuts for damage and fluid leakage.

4.Check brake hose mounting bracket for crack or deformation.

- Installation

1.To install, reverse the removal procedure.

   

• Use a new washer (A) whenever installing.

2.After installing, bleed the brake system. (Refer to Brake System - "Brake System Bleeding")(Refer to Brake System - "ABS System Bleeding")(Refer to Brake System - "ESP System Bleeding")

3.Check the spilled brake oil.

Other information:

Hyundai Accent (HC) (2017 - 2022) Service Manual: Power Door Lock Actuators

- Inspection Front Door Lock Module Inspection 1.Remove the front door trim.(Refer to Body - "Front Door Trim") 2.Remove the front door module.(Refer to Body - "Front Door Module") 3.Disconnect the connectors from the actuator. NoPin Information LHRH 1Motor 1Lock / UnLock switch 2Motor 2COM 3-Key Lock switch 4Key Unlock switchKey Unlock switch 5Key Lock switch- 6COMMotor 2 7Lock / UnLock switchMotor 1 4.

Hyundai Accent (HC) (2017 - 2022) Service Manual: Power Window Switch

- Circuit Diagram Power Window Main Swtich Front+Rear, Door Lock + Drive Safety Front+Rear, Door Lock, Auto Down Front Only, Door Lock, Auto Dwon Front+Rear, Auto Down Front Only, Auto Dwon Assist Power Window Switch (Manual) Rear Power Window Switch (Manual) - Inspection Power Window Main Switch Inspection 1.

Categories


 
Copyright © 2025
0.006