Contents:
1. Cowl side trim
2. Center pillar lower trim
3. Rear door scuff trim
4. Rear wheel house trim
5. Front pillar trim
6. Front door scuff trim
7. Center pillar upper trim
8. Rear pillar trim
1. Front door scuff trim
2. Rear door scuff trim
[Front door scuff trim]
• Put on gloves to prevent hand injuries.
• When removing with a flat - tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.
• When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.
• Take care not to bend or scratch the trim and panels.
1.Carefully remove the front door body side weatherstrip.
2.Using a screwdriver or remover, remove the front door scuff trim (A).
3.To install, reverse the removal procedure.
• Replace any damaged clips (or pin - type retainers).
[Rear door scuff trim]
• Put on gloves to prevent hand injuries.
• When removing with a flat - tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.
• When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.
• Take care not to bend or scratch the trim and panels.
1.Carefully remove the rear door body side weatherstrip.
2.Remove the rear seat cushion assembly. (Refer to Rear Seat - "Rear Seat Assembly")
3.Loosen the mounting screws and remove the rear door scuff trim (A).
4.To install, reverse the removal procedure.
• Replace any damaged clips (or pin - type retainers).
1. Cowl side trim
• Put on gloves to prevent hand injuries.
• When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.
• When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.
• Take care not to bend or scratch the trim and panels.
1.Remove the front door scuff trim.(Refer to Interior Trim - "Door Scuff Trim")
2.Carefully remove the front door body side weatherstrip.
3.Using a screwdriver or remover, remove the cowl side trim (A).
4.To install, reverse the removal procedure.
• Replace any damaged clips (or pin - type retainers).
1. Front pillar trim
• Put on gloves to prevent hand injuries.
• When removing with a flat - tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.
• When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.
• Take care not to bend or scratch the trim and panels.
1.Remove the front pillar trim.
(1)To remove the front pillar trim, the fastener remover (A) below must be used.
(2)After slightly lifting up the front pillar trim and putting the tool in, remove the mounting clip (A) by pulling it.
• Be sure to replace the existing clips with new ones when removing or replacing the front pillar trim.
(3)Remove the front pillar trim (A).
2.To install, reverse the removal procedure.
• Replace any damaged clips (or pin - type retainers).
• Be sure to replace the existing clips with new ones when removing or replacing the front pillar trim.
1. Center pillar lower trim
2. Center pillar upper trim
• Put on gloves to prevent hand injuries.
• When removing with a flat - tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.
• When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.
• Take care not to bend or scratch the trim and panels.
1.Carefully remove the front door body side weatherstrip.
2.Carefully remove the rear door body side weatherstrip.
3.Remove the front door scuff trim.(Refer to Interior Trim - "Door Scuff Trim")
4.Remove the rear door scuff trim.(Refer to Interior Trim - "Door Scuff Trim")
5.Using a screwdriver or remover, remove the center pillar lower trim (A).
6.To install, reverse the removal procedure.
• Replace any damaged clips (or pin - type retainers).
• Put on gloves to prevent hand injuries.
• When removing with a flat - tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.
• When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.
• Take care not to bend or scratch the trim and panels.
1.Remove the center pillar lower trim.(Refer to Interior Trim - "Center Pillar Trim")
2.Remove the anchor seat belt connector. (Refer to Restraint - "Emergency Fastening Device (EFD)")
3.Using a screwdriver or remover, remove the center pillar upper trim (A).
4.To install, reverse the removal procedure.
• Replace any damaged clips (or pin - type retainers).
1. Rear transverse trim
• Put on gloves to prevent hand injuries.
• When removing with a flat - tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.
• When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.
• Take care not to bend or scratch the trim and panels.
1.Remove the luggage covering met (A).
2.Loosen the mounting clips and remove the rear transverse trim (A).
3.To install, reverse the removal procedure.
• Replace any damaged clips (or pin - type retainers).
1. Luggage side trim
• Put on gloves to prevent hand injuries.
• When removing with a flat - tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.
• When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.
• Take care not to bend or scratch the trim and panels.
1.Remove the rear seat assembly(Refer to Rear Seat - "Rear Seat Assembly")
2.Carefully remove the rear door body side weatherstrip.
3.Remove the rear door scuff trim.(Refer to Interior Trim - "Door Scuff Trim")
4.Remove the rear transverse trim.(Refer to Interior Trim - "Rear Transverse Trim")
5.Loosen the mounting clips and screws, remove the luggage partition center trim (A).
6.Using a screwdriver or remover, remove the rear wheel house trim (A).
7.After loosening the mounting clips and screws, remove the luggage side trim (A).
8.To install, reverse the removal procedure.
• Replace any damaged clips (or pin - type retainers).
1. Rear pillar trim
• Put on gloves to prevent hand injuries.
• When removing with a flat - tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.
• When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.
• Take care not to bend or scratch the trim and panels.
1.Slighty remove the rear door body side weatherstrip.
2.Using a screwdriver or remover, remove the rear pillar trim (A).
3.To install, reverse the removal procedure.
• Replace any damaged clips (or pin - type retainers).
• Be sure to replace the existing clip (B) with new ones when removing or replacing the rear pillar trim.
1. Package tray trim
• Put on gloves to prevent hand injuries.
• When removing with a flat - tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.
• Use a plastic panel removal tool to remove interior trim pieces without marring the surface.
• Take care not to bend or scratch the trim and panels.
1.Remove the rear seat cushion assembly.(Refer to Rear Seat - "Rear Seat Assembly")
2.Remove the rear seat back assembly.(Refer to Rear Seat - "Rear Seat Assembly")
3.Slighty remove the rear door weatherstrip.
4.Remove the rear door scuff trim.(Refer to Interior Trim - "Door Scuff Trim")
5.Remove the rear pillar trim.(Refer to Interior Trim - "Rear Wheel House Trim")
6.Loosen the clips and screws, remove the luggage partition center trim (A).
7.Using a screwdriver or remover, remove the rear wheel house trim (A).
8.After loosening the mounting bolt, remove the rear seat belt lower anchor (A).
Tightening torque :39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.8 - 39.8 lb-ft)
[Side]
9.Using a screwdriver or remover, remove the center seat belt cover (A).
10.Using a screwdriver or remover, remove the package tray trim (A).
11.Disconnect the connector (A).
12.To install, reverse the removal procedure.
• Replace any damaged clips (or pin - type retainers).
Hyundai Accent (HC) (2017 - 2022) Service Manual: Front Stabilizer Bar
- Removal 1.Loosen the wheel nuts slightly.Raise the vehicle, and make sure it is securely supported. 2.Remove the front wheel and tire (A) from the front hub.Tightening torque :107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft) • Be careful not to damage the hub bolts when removing the front wheel and tire. 3.Hyundai Accent (HC) (2017 - 2022) Service Manual: Troubleshooting
- Troubleshooting SymptomPossible CauseRemedy One lamp does not light(all exterior)Bulb burned outReplace bulb Socket, wiring or ground faultyRepair if necessary Head lamps do not lightBulb burned outReplace bulb Ignition fuse (LOW:10A, HIGH:20A) blownCheck for short and replace fuse Head lamp fuse (15A) blownCheck for short and replace fuse Head lamp relay faultyCheck relay Lighting switch faultyCheck switch Wiring or ground faultyRepair if necessary Tail lamps and license plate lamp