Hyundai Accent (HC): Maintenance / Light bulbs

Contents:

• Headlamp, Position lamp, Fog lamp, Daytime Running Light, Turn Signal Lamp and Side Marker
• Side Repeater Lamp Replacement
• Rear Combination Light Bulb Replacement
• High Mounted Stop Lamp Replacement
• License Plate Light Bulb Replacement

Consult an authorized HYUNDAI dealer to replace most vehicle light bulbs. It is difficult to replace many Hyundai Accent light bulbs because other parts of the vehicle must be removed before you can get to the bulb. This is especially true when removing the headlamp assembly to access certain bulb(s), or when LED components are integrated into the lamp housing.

Removing/installing the headlamp assembly can result in damage to the vehicle if done incorrectly. For the best results on your Hyundai Accent (proper sealing, correct aiming, and reliable operation), have difficult lamp service performed by a qualified technician.

Information

The headlamp and tail lamp lenses could appear frosty if the vehicle is washed after driving or the vehicle is driven at night in wet weather. This condition is caused by temperature difference between the lamp inside and outside and, it does not indicate a problem with your vehicle. When moisture condenses in the lamp, it will be removed after driving with the headlamp on. The removable level may differ depending on lamp size, lamp position and environmental condition. However, if moisture is not removed after normal driving, or if water pools inside the lamp, have your Hyundai Accent inspected by an authorized HYUNDAI dealer.

WARNING

• Prior to replacing a lamp, depress the foot brake, move the shift lever into P (Park) apply the parking brake, place the ignition switch to the LOCK/OFF position, and take the key with you when leaving the vehicle to avoid sudden movement of the vehicle and to prevent possible electric shock.
• Be aware the bulbs may be hot and may burn your fingers.

Headlamp, Position lamp, Fog lamp, Daytime Running Light, Turn Signal Lamp and Side Marker

Type A

(1) Headlamp (High/Low)
(2) Front turn signal lamp/ Position lamp
(3) Side marker
(4) Front fog lamp*

WARNING

• Handle halogen bulbs with care. Halogen bulbs contain pressurized gas that will produce flying pieces of glass that could cause injuries if broken.
• Wear eye protection when changing a bulb. Allow the bulb to cool down before handling it.
• Always handle them carefully, and avoid scratches and abrasions. If the bulbs are lit, avoid contact with liquids.
• Never touch the glass with bare hands. Residual oil may cause the bulb to overheat and burst when lit.
• A bulb should be operated only when installed in a headlamp.
• If a bulb becomes damaged or cracked, replace it immediately and carefully dispose of it.

Headlamp (Halogen bulb)

1. Open the hood.
2. Disconnect the negative battery cable.
3. Remove the headlamp bulb cover by turning it counterclockwise.
4. Disconnect the headlamp bulb socket-connector.
5. Unsnap the headlamp bulb retaining wire by pressing the end and pushing it upward.
6. Remove the bulb from the headlamp assembly.
7. Install a new headlamp bulb and snap the headlamp bulb retaining wire into position by aligning the wire with the groove on the bulb.
8. Connect the headlamp bulb socket-connector.
9. Install the headlamp bulb cover by turning it clockwise.

Information

The headlamp aiming should be adjusted after an accident or after the headlamp assembly is reinstalled at an authorized HYUNDAI dealer.

Turn signal lamp / Position lamp

1. Open the hood.

2. Disconnect the negative battery cable.

3.Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.

4.Remove the bulb from the socket by pressing it in and rotating it counterclockwise until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket.

5.Insert a new bulb by inserting it into the socket and rotating it until it locks into place.

6.Install the socket in the assembly by aligning the tabs on the socket with the slots in the assembly.

7.Push the socket into the assembly and turn the socket clockwise.

Side marker

1. Open the hood.

2. Disconnect the negative battery cable.

3. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.

4. Remove the bulb from the socket by pulling out the bulb.

5. Insert a new bulb.

Front fog lamp

1. Loosen the pin-type retainers of the under cover and then remove the undercover.

2. Reach your hand into the back of the front bumper.

3. Disconnect the power connector from the socket.

4. Remove the bulb-socket from the housing by turning the socket counterclockwise until the tabs on the socket align with the slots of the housing.

5. Install a new bulb-socket into the housing by aligning the tabs on the socket with the slots in the housing. Push the socket into the housing and turn the socket clockwise.

Type B

(1) Headlamp (High/Low)
(2) Front turn signal lamp
(3) Side marker
(4) Position lamp / Daytime running lamp*
(5) Front fog lamp*

WARNING

• Handle halogen bulbs with care. Halogen bulbs contain pressurized gas that will produce flying pieces of glass that could cause injuries if broken.
• Wear eye protection when changing a bulb. Allow the bulb to cool down before handling it.
• Always handle them carefully, and avoid scratches and abrasions. If the bulbs are lit, avoid contact with liquids.
• Never touch the glass with bare hands. Residual oil may cause the bulb to overheat and burst when lit.
• A bulb should be operated only when installed in a headlamp.
• If a bulb becomes damaged or cracked, replace it immediately and carefully dispose of it.

Headlamp (Halogen Bulb)

1. Open the hood.
2. Disconnect the negative battery cable.
3. Remove the headlamp bulb cover by turning it counterclockwise.
4. Disconnect the headlamp bulb socket-connector.
5. Remove the bulb from the headlamp assembly.
6. Install a new headlamp bulb and snap the headlamp bulb retaining wire into position by aligning the wire with the groove on the bulb.
7. Connect the headlamp bulb socket-connector.
8. Install the headlamp bulb cover by turning it clockwise.

Information

The headlamp aiming should be adjusted after an accident or after the headlamp assembly is reinstalled at an authorized HYUNDAI dealer.

Headlamp (LED lamp)

If the LED lamp does not operate, have the vehicle checked by an authorized HYUNDAI dealer.

Turn signal

1. Open the hood.

2. Disconnect the negative battery cable.

3. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.

4. Remove the bulb from the socket by pressing it in and rotating it counterclockwise until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket.

5. Install a new bulb by inserting it into the socket and rotating it until it locks into place.

6. Install the socket in the assembly by aligning the tabs on the socket with the slots in the assembly.

7. Push the socket into the assembly and turn the socket clockwise.

Side marker & Position lamp/ Daytime running lamp

Your vehicle is equipped with LED lamps. LED lamps do not have replaceable bulbs. If the LED lamp does not operate, have the vehicle checked by an authorized HYUNDAI dealer.

Front fog lamp

1. Loosen the pin-type retainers of the under cover and then remove the undercover.

2. Reach your hand into the back of the front bumper.

3. Disconnect the power connector from the socket.

4. Remove the bulb-socket from the housing by turning the socket counterclockwise until the tabs on the socket align with the slots of the housing.

5. Install a new bulb-socket into the housing by aligning the tabs on the socket with the slots in the housing. Push the socket into the housing and turn the socket clockwise.

Side Repeater Lamp Replacement

On the Hyundai Accent, the side repeater (side turn signal) lamp may be a sealed unit depending on trim. If the signal is dim, flickers, or stops working, first confirm the turn signals are operating correctly and inspect the lens area for cracks or moisture.

â–  Type A

â–  Type B

If the light bulb does not operate, or if the lamp is LED and not serviceable, have the vehicle checked by an authorized HYUNDAI dealer. As a helpful extra step for Hyundai Accent owners, you can also verify the related fuse and connector seating before arranging service.

Rear Combination Light Bulb Replacement

When replacing rear bulbs on your Hyundai Accent, work on a cool vehicle, protect painted surfaces, and avoid pulling on wiring. Always install the correct bulb type and wattage to maintain proper visibility and safe signaling.

(1) Rear turn signal lamp
(2) Reverse lamp
(3) Stop/Tail lamp
(4) Tail lamp
(5) Side marker

Stop/Tail lamp and turn signal lamp

1. Open the trunk.

2. Open the lamp assembly retaining screw covers to access the fasteners.

3. Loosen the lamp assembly retaining screws with a cross-tip screwdriver, and keep the screws in a safe place.

4. Remove the rear combination lamp assembly from the body of the vehicle using steady, even pressure.

5. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.

6. Remove the bulb from the socket by pressing it in and rotating it counterclockwise until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket.

7. Insert a new bulb by inserting it into the socket and rotating it until it locks into place. Confirm it seats fully and does not wobble.

8. Install the socket into the assembly by aligning the tabs on the socket with the slots in the assembly. Push the socket into the assembly and turn the socket clockwise until it locks.

9. Reinstall the lamp assembly to the body of the vehicle, ensuring the gasket is seated to help prevent water intrusion.

Side marker

Your Hyundai Accent may be equipped with LED lamps. LED lamps do not have replaceable bulbs. If the LED lamp does not operate, have the vehicle checked by an authorized HYUNDAI dealer.

Tail lamp and backup lamp

1. Open the trunk.

2. Remove the service cover using a flat-blade screwdriver, taking care not to mar the trim.

3. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.

4. Pull the bulb out of the socket.

5. Insert a new bulb into the socket.

6. Install the socket into the assembly by aligning the tabs on the socket with the slots on the assembly and turning the socket clockwise.

7. Reinstall the service cover.

High Mounted Stop Lamp Replacement

For safe brake light performance on the Hyundai Accent, verify the high-mounted stop lamp illuminates evenly and replace failed bulbs promptly.

1.Open the trunk.

2. Remove the socket by turning it counterclockwise until the tabs on the socket align with the slots.

3. Remove the bulb from the socket by pressing it in and rotating it counterclockwise until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket.

4. Insert a new bulb by inserting it into the socket and rotating it until it locks into place.

5. Install the socket in the assembly by aligning the tabs on the socket with the slots in the assembly. Push the socket into the assembly and turn the socket clockwise.

6. Remove the high mounted stop lamp after removing the mounting nuts.

7. Install a new lamp and confirm all fasteners are secure.

8. Reinstall the rear spoiler and the trunk upper trim in the reverse order.

License Plate Light Bulb Replacement

Clean, bright license plate lights improve nighttime visibility and help keep your Hyundai Accent street-legal.

1. Using a flat-blade screwdriver, gently pry the lens cover from the lamp housing.

2. Remove the bulb by pulling it straight out.

3. Install a new bulb, making sure it is fully seated.

4. Reinstall in the reverse order.

Map lamp, room lamp, vanity mirror lamp and luggage compartment lamp

Interior lamp replacement on the Hyundai Accent is straightforward, but always use gentle pressure to avoid cracking lenses or breaking tabs.

â–  Map lamp

â–  Room lamp

â–  Trunk room lamp

1. Using a flat-blade screwdriver, gently pry the lens from the interior lamp housing.

2. Remove the bulb by pulling it straight out.

3. Install a new bulb in the socket.

4. Align the lens tabs with the interior lamp housing notches and snap the lens into place, checking that it sits flush.

WARNING

Prior to working on the Interior Lights, ensure that the "OFF" button is depressed to avoid burning your fingers or receiving an electric shock.

NOTICE

Use care not to dirty or damage lens, lens tab, and plastic housings. If fingerprints contact a bulb, wipe it clean with a soft cloth before reinstalling.