Hyundai Accent (HC): SRSCM / Occupant Classification System (OCS)

Hyundai Accent (HC) (2017 - 2022) Service Manual / Restraint / SRSCM / Occupant Classification System (OCS)

- Description In order to make normal activation of airbag system, SRSCM detects DTC(s) for the Occupant Classification System (OCS). If the seat is occupied, OCS detects passenger presences status and send signal to SRSCM via CAN.SRSCM recognizes the signal as 2 (two) different classifications; that is, 1 (Empty or small occupant with child restraint system), 2 (Occupied with large occupant and small occupant).With these signal, ACU determines whether it needs to deploy the PAB (Passenger Airbag) or not. - Components

1. OCS (Occupant Classification System) Unit
2. OCS (Occupant Classification System) Sensor
3. Passenger Seat


- Removal [OCS ECU ]

1.Disconnect the battery negative cable, and wait for at least three minutes before beginning work.

2.Remove the front passenger seat assembly.(Refer to Body - "Front Seat Assembly")

3.Disconnect the OCS ECU connector (A).

4.Remove the OCS mounting bolts.

[OCS Mat ]

1.Disconnect the battery negative cable, and wait for at least three minutes before beginning work.

2.Remove the front passenger seat assembly.(Refer to Body - "Front Seat Assembly")

3.Remove the front seat cushion cover.(Refer to Body - "Front Seat Cusion Cover")

4.Remove the front seat cushion assembly.(Refer to Body - "Front Seat Cushion Cover")

- Installation [OCS ECU ]

1.Install the occupant classification system unit on the Front seat track assembly.

2.Connect the occupant classification system unit connector.

3.Install the front passenger seat assembly.(Refer to Body - "Front Seat Assembly")

4.Reconnect the battery negative cable.

5.After installing the occupant classification system, confirm proper system operation.

   

• Turn the ignition switch ON the SRS indicator should be turned on for about six seconds and then go off.

• Telltale lamp will turn on for 4 seconds and be turned off for 3 seconds. After the 7 seconds, it shall remain off if the OCS does not require suppression and the passenger airbag is enabled.

• Be sure to perform OCS zeroing with GDS after replacing OCS equipped seat cushion.

- OCS Rest Procedure You should perform OCS Reset procedure after service or replacement about all part of the passenger seat. (Not included full seat assembly)

1.Ignition "OFF", connect GDS.

2.Ignition "ON" & Engine "OFF", select Airbag system and "Body Sensor Reset" mode.

3.The GDS will show the two OCS Reset function steps.

(1)Erase OCS diagnostic codes.

(2)OCS initialization.

   

• This Step must be done during front passenger seat empty.

4.Select product configuration.

(1)C1 : No heater

(2)C2 : Heater

   

• Before the starting the OCS Rest process, cross check seat correct configuration with actual vehicle.

• If you see the center console, you can find different buttons per each different seat configuration type. (Refer to the below picture)

5.The OCS initialization procedure will be performed.C1 : No Heater Type Reset

C2 : Heater Type Reset (Including Cooling Seat)

   

• Erase the SRSCM diagnostic codes after completing the OCS reset.

DTC CodeCode NameDescription
B1763ECU Defect
1.
Reset (Calibration setting) is not completed
2.
ECU is damaged from physical stress
B1764MAT Defect
1.
Mat and ECU are not connected .
2.
Mat is damaged from physical stress.
B1767Algo cut-off
1.
Too much humidity.
B1111IGN voltage high
1.
IGN voltage high.
B1112IGN voltage low
1.
IGN voltage low.
B1603CAN bus off
1.
CAN Bus is not working.
B1697ACU communication error
1.
CAN Bus is not working.
2.
ACU is not working.

Other information:

Hyundai Accent (HC) (2017 - 2022) Service Manual: A/C Pressure Transducer

- Description The A/C Pressure Transducer (APT) converts the pressure value of high pressure line into voltage value after measuring it. By converted voltage value, engine ECU controls the cooling fan by operating it high speed or low speed. Engine ECU stops the operation of the compressor when the temperature of refrigerant line is very high or very low irregularly to optimize air conditioning system.

Hyundai Accent (HC) (2017 - 2022) Service Manual: Manual Transaxle

- Components 1. Control shaft complete2. Manual transaxle case3. Clutch housing4. Back-up lamp switch5. Manual transaxle support bracket6. Control cable bracket - Removal 1.Turn OFF ignition switch and disconnect the negative (-) battery cable. 2.Remove the air cleaner assembly and air duct.(Refer to Engine Mechanical System - "Air cleaner") 3.

Categories


 
Copyright © 2025
0.005