Hyundai Accent (HC): Brake System / Rear Drum Brake

- Components

1. Shoe hold down pin
2. Shoe adjuster
3. Upper return spring
4. Adjusting lever
5. Shoe
6. Adjusting spring
7. Lower return spring
8. Shoe hold spring


- Removal

1.Loosen the wheel nuts slightly. Raise the vehicle, and make sure it is securely supported.

2.Remove the rear wheel and tire (A).

Tightening torque :107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)

   

• Be careful not to damage the hub bolts when removing the rear wheel and tire.

3.Loosen the screw and then remove the drum.

Tightening torque :4.9 - 5.9 N.m (0.5 - 0.6 kgf.m, 3.6 - 4.3 lb-ft)

4.Remove the upper shoe return spring (A), lower shoe return spring (B), level pawl (C) and djuster assembly (D).

5.Remove the adjusting spring (A).

6.Remove the shoe hold assembly (A) and then remove the brake shoe.

7.Disconnect the parking cable.

8.Disconnect the brake fluid tube flare nut (A).

Tightening torque :12.7 - 16.7 N.m (1.3 - 1.7 kgf.m, 9.4 - 12.3 lb-ft)

9.Loosen the mounting bolts (A) and then remove the wheel cylinder (B) from the backing plate (C).

10.Install in the reverse order of removal.

11.After installation, bleed the brake system. (Refer to Brake System - "Brake System Bleeding")(Refer to Brake System - "ESP System Bleeding")(Refer to Brake System - "ABS System Bleeding")

- Inspection

   

• Frequent inhalation of brake pad dust, regardless of material composition, could be hazardous to your health.

• Avoid breathing dust particles.

• Never use an air hose or brush to clean brake assemblies.

   

• Contaminated brake linings or drums reduce stopping ability.

• Block the front wheels before jacking up the rear of the vehicle.

1.Raise the rear of the vehicle, and make sure it is securely supported.

2.Release the parking brake, and remove the rear brake drum.

3.Check the wheel cylinder (A) for leakage.

4.Check the brake linings (B) for cracking, glazing, wear, and contamination.

5.Measure the brake lining thickness (C).Measurement does not include brake shoe thickness.

Brake lining thicknessStandard : 4.5 mm (0.177 in)Service limit : 1.0 mm (0.039 in)

6.If the brake lining thickness is less than the service limit, replace the brake shoes as a set.

7.Check the bearings in the hub unit for smooth operation. If it requires servicing, replace it.

8.Measure the inside diameter of the brake drum with inside vernier calipers.

Drum inside diameterStandard : 205.3 mm (9.0 in)Service limit : 207.3 mm (9.08 in)Drum roundnessService limit : 0.06 mm (0.00236 in)

9.If the inside diameter of the brake drum is more than the service limit, replace the brake drum.

10.Check the brake drum for scoring, grooves, and cracks.

11.Inspect the brake lining and drum for proper contact.

12.Inspect the wheel cylinder outside for excessive wear and damage.

13.Inspect the backing plate for wear or damage.

Other information:

Hyundai Accent (HC) (2017 - 2022) Service Manual: General Safety Information and Caution

- Precautions General Precautions Please read the following precautions carefully before performing the airbag system service. Observe the instructions described in this manual, or the airbags could accidentally deploy and cause damage or injuries. • Except when performing electrical inspections, always turn the ignition switch OFF and disconnect the negative cable from the battery, and wait at least three minutes before beginning work.

Hyundai Accent (HC) (2017 - 2022) Service Manual: Engine Control Module (ECM)

- ECM Terminal and Input/Output signal [M/T] ECM Terminal Function (M/T) Connector [A] Pin NoDescription 1- 2- 3Injector (Cylinder #1-1) [Low] control output 4Injector (Cylinder #1-2) [Low] control output 5- 6- 7- 8- 9- 10- 11Electric EGR Control Valve gorund 12Engine Coolant Temperature Sensor (ECTS) #2 ground 13Ignition Coil (Cylinder #1) control output 14- 15Ignition Coil (Cylinder #4) control output 16Thermal Management Module (TMM) Motor ground 17- 18Engine Cool

Categories


 
Copyright © 2025
0.0067