Hyundai Accent (HC): Suspension System / Specifications

- Specifications Front Suspension

ItemSpecification
Suspension typeMac Pherson Strut
Shock absorberTypeGeneral Valve

Rear Suspension
ItemSpecification
Suspension type Couple Torsion Beam Axle
Shock absorberTypeGeneral Valve

Wheel & Tire
ItemSpecification
WheelAluminum5.5J * 15
6.5J * 17
Steel5.5J * 15
Tire 185/65 R15
205/45 R17
Spare tire T125/80 R15
Tire pressure kg/cm² (psi)185/65 R15 230 (33)
205/45 R17230 (33 )
T125/80 R15420 (60)

Wheel Alignment
ItemSpecification
FrontToe-in Total0.15° ± 0.2°
Individual0.075° ± 0.1°
Camber angle-0.5 ± 0.5°
Caster angle4.64° ± 0.5°
King-pin angle13.23° ± 0.5°
Ride Height367 ± 10 mm (14.4488 ± 0.3937 in)
RearToe-inTotal0.3° ± 0.3°
Individual0.15° ± 0.15°
Camber angle-1.5° ± 0.5°
Ride Height
(Full fuel condition)
368 ± 10 mm (14.4881 ± 0.3937 in)

- Tightening Torques Front Suspension
ItemTightening torque (kgf.m)
N.mkgf.mlb-ft
Hub nuts107.9 - 127.511.0 - 13.079.6 - 94.0
Front strut assembly to front axle98.1 - 117.10.0 - 12.072.3 - 86.
Front strut assembly to body49.0 - 58.85.0 - 6.036.2 - 43.4
Lower arm to sub frame (Front)117.7 - 137.312.0 - 14.086.8 - 101.3
Lower arm to sub frame (Rear)156.9 - 176.516.0 - 18.0115.7 - 130.2
Lower arm to knuckle58.8 - 70.66.0 - 7.243.4 - 52.1
Tie rod end castle nut23.5 - 33.42.4 - 3.417.4 - 24.5
Steering gear box to sub frame88.3 - 107.99.0 - 11.065.1 - 79.6
Stabilizer bar to stabilizer link98.1 - 117.710.0 - 12.072.3 - 86.8
Stabilizer bar to sub frame44.1 - 53.94.5 - 5.532.5 - 39.8
Stabilizer bar to front strut assembly98.1 - 117.710.0 - 12.072.3 - 86.8
Sub frame mounting to body bolt & nut176.5 - 196.118.0 - 20.0130.2 - 144.7
Bolt connecting universal joint to pinion (M8 BOLT)32.4 - 37.33.3 - 3.823.9 - 27.5
Bolt connecting universal joint to pinion (M10 BOLT)49.0 - 58.85.0 - 6.036.2 - 43.4
Roll rod bracket to roll rod support bracket fixing bolt & nut107.9 - 127.511.0 - 13.079.6 - 94.0

Rear Suspension
ItemTightening torque (kgf.m)
N.mkgf.mlb-ft
Hub nuts107.9 - 127.511.0 - 13.079.6 - 94.0
Shock absorber to body49.0 - 63.75.0 - 6.536.2 - 47.0
Shock absorber to torsion beam axle98.1 - 117.710.0 - 12.072.3 - 86.8
Torsion beam axle to body117.7 - 137.312.0 - 14.086.8 - 101.3
Bitmap Torsion beam axle to brake caliper63.7 - 73.56.5 - 7.547.0 - 54.2
Shock absorber lock nut19.6- 24.52.0 - 2.514.5 - 18.1

Other information:

Hyundai Accent (HC) (2017 - 2022) Service Manual: Temperature Control Actuator

- Components Location 1. Temperature control actuator - Description The temperature control actuator is located at the heater unit. It regulates the temperature by the procedure as follows. The signal from the control unit adjusts the position of the temperature door by operating the temperature switch. Then the temperature will be regulated by the hot/cold air ratio decided by the position of the temperature door.

Hyundai Accent (HC) (2017 - 2022) Service Manual: General Service Information

- General Service Information Protection of the VehicleAlways be sure to cover fenders, seats, and floor areas prior to beginning work.     • The support rod must be inserted into the hole near the edge of the hood whenever you inspect the engine compartment to prevent the hood from falling and causing possible injury. • Make sure that the support rod has been released prior to closing the hood.

Categories


 
Copyright © 2025
0.0059